Browsing by Author "Abbas, B. A."

Now showing 1 - 10 of 10

A Comparative Analysis of Grillage Method and Beam line Analysis of a Reinforced Concrete Waffle Brifge Deck
(Nigeria Journal of Engineering and Applied Sciences (NJEAS), 2022-01-23) Adamu, H. N.; Abbas, B. A.; Abubakar, M.; Yusuf, A.; Kolo, D. N.; Shehu, M.
The analysis of reinforced concrete waffle bridge deck using Chanchaga bridge as a case study was carried out with the aid of computer program written in MATLAB. The bridge deck which is a beam bridge was idealized to be a waffle slab. A mathematical model of the bridge was developed using the method of grillages because very complex shapes of problem domain with prescribed conditions can be handled easily using the method. The bridge deck was modelled as interconnection of grid elements. The analysis was carried out using direct stiffness matrix method. The nodal displacements and the resulting static internal forces; shear forces, bending moments and twisting moments of each grid element were determined using the matrix. The results obtained using the method of grillages were then compared with beam line analysis and the former method gave a 10% decrease in forces which will result in the reduction of overall design and materials by 10%.
Effect of Partial Replacement of Cement with Cow Dung Ash Using Bida Natural Coarse Aggregate
(2023-02-04) Abbas, B. A.; Yusuf, A.; Kolo, D. N.; Aboje, A. A.; Mahmud, M. B.; Ndaiji, A. U.
The research investigates the effect of partial replacement of cement with cow dung ash (CDA) in concrete production using Bida natural coarse aggregate. Water to cement ratio and mix ratio of 0.6 and 1:2:4 was adopted respectively. The aggregates used were characterized and the cow dung was calcined at a temperature between 400-500oC. Concrete was produced using CDA as cement replacement at 0%, 5%, 10%, 15%, 20%, 25%, 30%, 35% and 40%. Slump of the freshly produced concrete was determined and the compressive strength of the hardened concrete was determined at 7, 21 and 28 days of curing. The sum of SiO2, Al2O3 and Fe2O3 in CDA exceeds the 70% minimum specified by ASTMC 618-12. The slump of the fresh concrete ranges from 0 – 40 mm while the compressive strength at 28 days curing duration ranges from 12.59N/mm2 19.29N/mm2 and density was 2323.95kg/m3 – 2554.59kg/m3 respectively. The test results revealed that the compressive strength decrease with increase in CDA content and increase with curing age. The strength results indicate that there was no much significant difference between the control specimen with 0% CDA and that containing 5% CDA. This implies that concrete made using CDA as partial replacement for cement can be used for structural applications such as in the construction of reinforced concrete slabs, beams, columns and foundations. The study concluded that CDA has pozzolanic properties and can be used to replace up to 10% cement in concrete produced using Bida natural coarse aggregate.
Effectiveness of Locust Bean Epicarp Extract on Re-vibrated Concrete Using Pebbles from Bida Environs as Coarse Aggregate
(Proceedings of the Sustainable Education and Development Research Conference, University of Environment and Sustainable Development, Somanya, Ghana, 2023-01-02) Abbas, B. A.; Mohammed, T. A.; Yusuf, A.; Kolo, D. N.; Abubakar, M.; Abdullahi, A.
Empirical Relationship between Compressive, Flexural and Splitting Tensile Strengths of Concrete Containing Kuta Gravel as Coarse Aggregate
(Journal of Engineering Research and Reports, 2025-02-02) Abubakar, J.; Abdullahi, M.; Aguwa, J. I.; Abbas, B. A.; Kolo, D. N.
Flexural and tensile strengths of concrete are of great importance in structural engineering. Understanding the flexural strength of concrete helps designers prevent and control development of cracks in concrete elements, ensuring durability. In addition to serviceability, shear, bond failure and flexural capacity in concrete members are directly linked to the tensile strength of the concrete. When compared to flexural and tensile strengths, determination of the compressive strength of concrete is easier to carry out in the field. It is therefore, customary to determine the compressive strength and correlate it to other strength properties. In this study, empirical relationships have been developed to relate the compressive strength to the flexural and splitting tensile strengths of concrete using Kuta river gravel as coarse aggregate. Using varying total aggregate to cement, coarse aggregate to total aggregate and water to cement ratios, 20 mixes were generated using Central Composite Design (CCD) in Minitab 21. The compressive, flexural and splitting tensile strengths of concrete samples from these mixes were determined at 28 days of age. From the strength data obtained, regression equations were developed that relate the strength properties with the aid of regression analysis tool in Microsoft Excel. The empirical models developed to predict the flexural and splitting tensile strengths of concrete from the compressive strength recorded R2 values of 1 for both models, P-values of 5.23 × 10−29 and 4.47 × 10−30, and standard errors of 0.21 and 0.06 respectively. Furthermore, residuals from the values of predicted strength properties show that there is very slight deviation between the experimental and predicted values. It was concluded that the empirical equations developed are significant, have high predictive capabilities and can be used in predicting the flexural and splitting tensile strengths of concrete.
Investigation into the Mechanical properties of concrete using Pebbles from Bida Environ as coarse aggregate in concrete production
(Polish Journal of Science, 2024-01-02) Abbas, B. A.; Abdullahi, M.; Sadiku S.; Aguwa J.I.; Abubakar J.; Kolo, D. N.
Strength performance remains the most important property of structural concrete, from engineering point of view. This paper investigates the mechanical properties of concrete made from Bida natural stones, extensive experimental work was conducted using 1,600 specimens for compressive strength, flexural strength, splitting tensile strength and elastic modulus (four hundred specimens for each property). Central composite design was used for the factor setting with the following range of values; W/C= 0.4, 0.5, 0.6, CA/TA= 0.55, 0.615, 0.68, TA/C= 3.0, 4.5 and 6.0. The specimens were produced and cured for 7, 14, 21 and 28days. The highest strength was achieved using low W/C, low TA/C and high level of CA/TA corresponding to 0.4, 3.0 and 0.68 respectively
Models to Predict the Fresh and Hardened Properties of Palm Kernel Shell Concrete
(Malaysian Journal of Civil Engineering, 2022-01-12) Kolo, D. N.; Tsado, T. Y.; Abbas, B. A.; Adamu, H. N.
Concrete is an assemblage of Cement, aggregates and water, the most frequently used fine aggregate for concrete production is sand sourced from river banks. The continuous exploitation of available granite conventionally used as coarse aggregate in concrete production coupled with rapid infrastructural development has resulted in its scarcity and often high cost. The suitability of utilising Palm Kernel Shell (PKS) as partial replacement for coarse aggregate in concrete production was examined in this paper. Preliminary tests were conducted on all aggregates to determine their suitability for concrete production. Concrete with 5, 10, 15, 20 and 25% PKS-coarse aggregate content was cast with a mix ratio of 1:2:4. The freshly prepared Palm Kernel Shell Concrete (PKSC) was cast in moulds measuring 150 x 150 x 150mm and cured using ponding method. The Compressive strength result shows that an increase in the PKS content results in a decrease in compressive strength of concrete. Linear regression models for the slump and compressive strength of the PKSC were developed and found to be sufficient in predicting the compressive strengths with R2 values of 96% and 92 % respectively.
Numerical Investigation of Reinforced Concrete Beam Containing Iron Ore Tailings as Partial Replacement of Sand
(Conference: 4 th International Conference on Innovations and Challenges in Engineering and Technology for Sustainable DevelopmentAt: Arba Minch University, Ethiopia, 2023) Abubakar, Mahmud; Haruna, M. I.; Abdulrahman, H. S.; Abbas, B. A.
The production of industrial and agricultural residual by-products can generate significant environmental impact. In response, researchers have begun incorporating supplementary materials made from agro-industrial wastes to create more sustainable concrete. However, testing the performance of these waste-based concrete mixtures can be time-consuming and expensive. To address this issue, this study utilized three dimensional non-linear Finite Element simulation using the ABAQUS/CAE software to predict the behavior of a reinforced concrete beam that incorporated 20% IOT as partial sand replacement. The simulation successfully predicted the damage behavior of the 20% IOT concrete, indicating the potential of this modeling approach to accurately predict the performance of waste-based concrete mixtures in various designs.
POTENTIAL OF CALCIUM CARBIDE RESIDUE MODIFIED SANDCRETE BLOCKS IN ENHANCING THERMAL AND ENERGY EFFICIENCY FOR SUSTAINABLE BUILDING DESIGN
(2nd Faculty of Engineering and Technology Conference (FETiCON 2024), Jun. 2 - 6, 2024, University of Ilorin, Nigeria, 2024) Ibrahim, M; Abubakar, Mahmud; Abdullahi, Aliyu; Abbas, B. A.
Sustainability has increasingly become a prominent topic in the field of construction, and as such, it is necessary to explore means of reducing the overdependence on the use of cement in construction works. This study investigated the effects of calcium carbide residue (CCR) as a partial substitute for cement in sandcrete blocks. Due to the high pH value of calcium carbide residue, its disposal in landfills increases the alkalinity of the environment. From raw material extraction through final product disposal, the construction industry is integrally involved in every stage of the lifecycle of greenhouse gas emissions. In this study, cement was partially substituted using CCR at 0% and 12% by weight replacement. The sandcrete blocks were of 450 mm × 225 mm × 225 mm dimensions and made from a Cement-CRR mix ratio of 1:6 and water-cement ratio of 0.6. Preliminary tests such as consistency, setting times, soundness, and specific gravity tests were carried out on cement and cement + 12% CCR. The thermal properties, which include thermal conductivity (k), heat transfer coefficient (U), specific heat capacity (Cp) and diffusivity (α) of the sandcrete blocks were determined. The thermal tests were carried out after the 28th day of curing. The result showed that CCR increased the water demand by the sandcrete blocks, hence reducing its workability. The sandcrete block samples made with 12% CCR replacement showed improved compressive strength. The k for 0% and 12% replacement was 0.5497 W/mK and 0.3978 W/mK, respectively, while the U was 54.974 W/m2K and 39.784 W/m2K, respectively for the 0% and 12% replacement. On the other hand, the Cp for 0% and 12% was 0.0003364 J/kg°C and 0.0001598 J/kg°C, respectively, while the diffusivity was 636.54m2/s and 1113.94m2/s for 0% and 12% replacement, respectively. As such, we can infer that 12% CCR replacement of cement gives more energy-efficient and sustainable sandcrete blocks.
Production of Pavement Blocks Using Low Density Polyethylene Product Waste
(SETIC 2022 International Conference: “Sustainable Development and Resilience of the Built Environment in the Era of Pandemic” School of Environmental Technology, Federal University of Technology, Minna 6th – 8th February, 2023., 2023) Aboje, A. A.; Abbas, B. A.; Kolo, D. N.; Abubakar, Mahmud; Abdulsalam, A.
Waste sachet water packs cause considerable land pollution in Nigeria. In this research, pavement block was produced using low density polyethylene products waste (sachet water packs) as an alternative binder. The production was achieved by first converting the sachet water packs into pellets and blending it with sandstone in a mass ratio of 8:2 (A), 7:3 (B) and 6:4 (C) sandstone to pellets respectively. The compressive strength, %water absorption and curing time tests were carried out on the pavement block to determine it suitability and safety for low-traffic use. The compressive strength for polymer concrete samples A, B and C were 13.65N/mm2, 16.99N/mm2 and 20.34N/mm2 respectively. After carrying out the %water absorption test on the polymer concrete A, B and C the following result was obtained: 8.33%, 5.47% and 4.03% respectively. It should be noted that the polymer concrete samples and the control samples which (are cement concrete based) are for light-traffic use (pedestrian, plazas, shopping complexes ramps, car parks, office drive ways, rural roads with low traffic, and residential road).
Production of Pavement Blocks Using Low Density Polyethylene Product Waste
(Proceedings of the 4th International Conference (SETIC), School of Environmental Technology, Federal University of Technology, Minna, Nigeria, 2023-01-02) Aboje, A. A.; Abbas, B. A.; Kolo, D. N.; Abubakar, M.; Abdulsalam A. M.
Waste sachet water packs cause considerable land pollution in Nigeria. In this research, pavement block was produced using low density polyethylene products waste (sachet water packs) as an alternative binder. The production was achieved by first converting the sachet water packs into pellets and blending it with sandstone in a mass ratio of 8:2 (A), 7:3 (B) and 6:4 (C) sandstone to pellets respectively. The compressive strength, %water absorption and curing time tests were carried out on the pavement block to determine it suitability and safety for low-traffic use. The compressive strength for polymer concrete samples A, B and C were 13.65N/mm2 , 16.99N/mm2 and 20.34N/mm2 respectively. After carrying out the %water absorption test on the polymer concrete A, B and C the following result was obtained: 8.33%, 5.47% and 4.03% respectively. It should be noted that the polymer concrete samples and the control samples which (are cement concrete based) are for light-traffic use (pedestrian, plazas, shopping complexes ramps, car parks, office drive ways, rural roads with low traffic, and residential road).