Civil Engineering
Permanent URI for this collectionhttp://197.211.34.35:4000/handle/123456789/148
Civil Engineering
Browse
4 results
Search Results
Item PARTIAL REPLACEMENT OF FINE AGGREGATE WITH WASTE GLASS IN CONCRETE MADE FROM BIDA NATURAL AGGREGATE(3rd International Engineering Conference (IEC 2019) Federal University of Technology, Minna, Nigeria, 2019) Alhaji, B.; Kolo, D. N.; Abubakar, Mahmud; Yusuf, A.; Abdullahi, A.; Mohammed, S.This study reports the experimental investigation on the suitability of waste glass as partial replacement for fine aggregate in concrete made using Bida natural aggregates (BNA). Glass is widely used in our daily lives through manufactured products such as sheet glass, bottles, glassware, and vacuum tubing. It is an ideal material for recycling. The increasing awareness of glass recycling speeds up inspections on the use of waste glass with different forms in various fields. Mix ratio of 1:2:4 batched by weight with water – cement ratio of 0.55 was used. The percentage replacement varied from 0% to 40% at 5% intervals. Slump test was conducted to assess the workability of the fresh concrete. The compressive strengths and densities of cured concrete cubes of sizes 150mm x 150mm x 150mm were evaluated at 7, 21 and 28days. A total of 81 concrete cubes were cast and tested. It was observed that an increase in the percentage replacement of fine aggregate with waste glass reduces workability, density and compressive strength. The compressive strength and density vary with days of curing. The findings of this study indicated that the optimum replacement percentage of waste glass with conventional fine aggregate was 20%. However waste glass can effectively be used as fine aggregate replacement (up to 40%) without substantial change in concrete strength.Item Partial Replacement of Fine Aggregate with waste Glass in Concrete made from Bida Natural Aggregate(. Proceedings of the 3rd International Engineering Conference, Federal University of Technology Minna, Nigeria, 2019-02-05) Alhaji, B.; Kolo, D. N.; Abubakar M.; Yusuf A.; Abdullahi, A.; Shehu, M.This study reports the experimental investigation on the suitability of waste glass as partial replacement for fine aggregate in concrete made using Bida natural aggregates (BNA). Glass is widely used in our daily lives through manufactured products such as sheet glass, bottles, glassware, and vacuum tubing. It is an ideal material for recycling. The increasing awareness of glass recycling speeds up inspections on the use of waste glass with different forms in various fields. Mix ratio of 1:2:4 batched by weight with water cement ratio of 0.55 was used. The percentage replacement varied from 0% to 40% at 5% intervals. Slump test was conducted to assess the workability of the fresh concrete. The compressive strengths and densities of cured concrete cubes of sizes 150mm x 150mm x 150mm were evaluated at 7, 21 and 28days. A total of 81 concrete cubes were cast and tested. It was observed that an increase in the percentage replacement of fine aggregate with waste glass reduces workability, density and compressive strength. The compressive strength and density vary with days of curing. The findings of this study indicated that the optimum replacement percentage of waste glass with conventional fine aggregate was 20%. However waste glass can effectively be used as fine aggregate replacement (up to 40%) without substantial change in concrete strength.Item Durability Characteristics of Lateritic Subgrade Treated with Iron Ore Tailings and Lime Exposed to Moisture Fluctuations(. Nigeria Journal of Engineering and Applied Sciences (NJEAS), 2018-02-11) Mohammed, A. M.; Amadi, A. A.; Aguwa, J. I.; Kolo, D. N.This research evaluated the durability of lateritic subgrade treated with Iron Ore Tailings (IOT) and lime exposed to moisture variations. Representative sample of the subgrade was treated with 0, 5, 10, 15, and 20% IOT and optimal lime percent (6.2%) determined through Eades and Grim pH test. Preliminary tests such as particles size distribution, Atterberg limits and compaction were conducted to characterize the mixtures while Unconfined Compressive Strength (UCS) and CBR-swell tests were carried out to access durability of the soil mixtures. Addition of lime to the soil increased the liquid limit to 45% from 36% obtained in natural soil. Similarly, the plastic limit of the lime-treated sample increased from 16 to 26% with reduced plasticity index. While the natural soil exhibited CBR of 3 and 75% for soaked and unsoaked specimens respectively, the value increased and peaked at 11 and 118% with addition of lime and 15% IOT. Durability of the soil improved with addition of IOT and lime. 15% IOT and lime treated soil recorded the best results with UCS of 240 kN/m2 and 200% Relative Volumetric Stability (RVS), which is a measure of strength loss of a soil. Similarly, swell value of 0% was recorded when the lime-IOT samples were subjected to CBR-Swell test. This shows that the lime-IOT treated samples are less vulnerable to moisture condition normally prevalent in the pavement subgrades.Item Development of Sensitivity based Model for Flexural Failure of Singly Reinforced Concrete Slabs Based on BS 8110: 1997(. Nigeria Journal of Engineering and Applied Sciences (NJEAS), 2017-03-22) Tsado, T.Y.,; Sadiku, S.,; Iorkar, A.; Kolo, D. N.This research presents mathematical models for checking the effect of variation in key designed parameters on the structural collapse of singly reinforced concrete solid slabs in buildings due to flexural failure based on British Standard (BS) 8110, 1997. The increasing complexity of construction process requires very high level of engineering and management skills to combat the structural collapses widely experienced globally. Most of the collapses were adjudged to be due to improper management arising from variations in structural key design parameters during construction, and this call for mathematical models to check the effect of variation in key design parameters on the structural collapse. The key design parameters considered in this research are; characteristic strength of reinforcement, grade of concrete, diameter and spacing of tension reinforcement, effective depth of tension reinforcement, applied moment. Sensitivity analysis was applied to study the effect of variation in the key parameters on the moment capacity. The results of sensitivity analysis were utilized in regression analysis to develop simplified equations for estimating the moment capacity of the slab. Computer programme was developed based on BS 8110, 1997 standard using Java to verify the model. Flexure safety factor was also checked based on BS 8110, 1997 requirements. Forty five numerical examples were taken to validate the model with the developed computer programme at 5% significance level using Chi-squared as an instrument for sensitivity-based model for flexural failure of singly reinforced concrete slab. The results show that the model is adequate at 5% significance level for checking flexural failure of singly reinforced concrete slab at construction stage based on BS 8110, 1997. It was recommended that the construction practitioners should consider the diverse effect of change in key deigned parameters during construction, otherwise the developed model should be strictly considered for quick safety check especially deflection safety of a solid slab during construction.